View ISL6557CB_403203.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
ISL6557
Data Sheet August 2003 FN9059.2
Multi-Phase PWM Controller for Core-Voltage Regulation
The ISL6557 provides core-voltage regulation by driving up to four interleaved synchronous-rectified buck-converter channels in parallel. Intersil multi-phase controllers together with Intersil MOSFET drivers form the basis for the most reliable power-supply solutions available to power the latest industry-leading microprocessors. Multi-phase buckconverter architecture uses interleaved timing to multiply ripple frequency and reduce input and output ripple currents. Lower ripple results in lower total component cost, reduced dissipation, and smaller implementation area. Preconfigured for 4-phase operation, the ISL6557 offers the flexibility of selectable 2- or 3-phase operation. Simply connect the unused PWM pins to VCC. The channel switching frequency is adjustable in the range of 50kHz to 1.5MHz giving the designer the ultimate flexibility in managing the balance between high-speed response and good thermal management. New features on the ISL6557 include Dynamic-VIDTM technology allowing seamless on-the-fly VID changes with no need for any additional external components. When the ISL6557 receives a new VID code, it incrementally steps the output voltage to the new level. Dynamic VID changes are fast and reliable with no output voltage overshoot or undershoot. The RGND and VSEN pins provide inputs for differential remote voltage sensing to improve regulation and protection accuracy. A threshold-sensitive enable pin (EN) can be used with an external resistor divider to optionally set the power-on voltage level. This allows optional start-up coordination with Intersil MOSFET drivers or any other devices powered from a separate supply. Like other Intersil multiphase controllers, the ISL6557 uses cost and space-saving rDS(ON) sensing for channel current balance, dynamic voltage positioning, and overcurrent protection. Channel current balancing is automatic and accurate with the integrated current-balance control system. Overcurrent protection can be tailored to any application with no need for additional parts. The IOUT pin carries a signal proportional to load current and can be optionally connected to FB for accurate load-line regulation. An integrated DAC decodes the 5-bit logic signal present at VID4-VID0 and provides an accurate reference for precision voltage regulation. The high-bandwidth error amplifier, differential remote-sensing amplifier, and accurate voltage reference all work together to provide better than 0.8% total system accuracy, and to enable the fastest transient response available.
Features
* Multi-Phase Power Conversion * Active Channel Current Balancing * Precision rDS(ON) Current Sensing - Low Cost - Lossless * Precision CORE Voltage Regulation - Differential Remote Voltage Sensing - 0.8% System Accuracy * Microprocessor Voltage Identification Input - Dynamic VID technology - 5-Bit VID Input - 1.100V to 1.850V in 25mV Steps * Programmable Power-On Bias Level * Programmable Droop Voltage * Fast Transient Recovery Time * Precision Enable Threshold * Overcurrent Protection * 2-, 3-, or 4-Phase Operation * High Ripple Frequency. Channel Frequency Times Number Channels (100kHz to 6MHz)
Ordering Information
PART NUMBER ISL6557CB ISL6557CB-T TEMP. (oC) 0 to 70 PACKAGE 24-Ld SOIC PKG. DWG. # M24.3
24-Ld SOIC Tape and Reel
Pinout
ISL6557 24 PIN (SOIC) TOP VIEW
VID4 1 VID3 2 VID2 3 VID1 4 VID0 5 COMP 6 FB 7 IOUT 8 VDIFF 9 VSEN 10 RGND 11 GND 12 24 VCC 23 EN 22 FS 21 PGOOD 20 PWM4 19 ISEN4 18 ISEN1 17 PWM1 16 PWM2 15 ISEN2 14 ISEN3 13 PWM3
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2003. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. Dynamic VIDTM is a trademark of Intersil Americas Inc.
ISL6557 Block Diagram
VDIFF
PGOOD
VCC
RGND
x1 + POWER-ON RESET (POR) UV + OV S LATCH CLOCK AND SAWTOOTH GENERATOR +
1.23V
EN
FS
VSEN
+ OVP -
+ + PWM PWM1
0.9V
2.1V + SOFTSTART AND FAULT LOGIC + PWM PWM2
COMP 2.5V VID0 VID1 VID2 VID3 VID4 DYNAMIC VID D/A + + E/A + PWM PWM4 + + PWM PWM3
FB
CURRENT CORRECTION PHASE NUMBER
CHANNEL DETECTOR
IOUT I_TOT OC +
IOC
+ + + +
ISEN1 ISEN2 ISEN3 ISEN4
GND
2
ISL6557 Typical Application, 4-Phase Buck Converter
+12V VIN
VCC PVCC
BOOT UGATE PHASE
PWM +5V
HIP6601A DRIVER LGATE GND
FB VDIFF VSEN RGND
IOUT
COMP VCC EN
+12V VIN
VCC PVCC
BOOT UGATE PHASE
PGOOD VID4 VID3 VID2 VID1 VID0 FS RT ISEN4 GND PVCC HIP6601A DRIVER ISL6557 PWM2 ISEN2 PWM3 ISEN3 PWM4 VCC +12V ISEN1 PWM PWM1 HIP6601A DRIVER
LGATE GND
VIN P LOAD BOOT UGATE PHASE
PWM
LGATE GND
+12V VIN
VCC PVCC
BOOT UGATE PHASE
PWM
HIP6601A DRIVER LGATE GND
3
ISL6557
Absolute Maximum Ratings
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7V Input, Output, or I/O Voltage . . . . . . . . . . GND -0.3V to VCC + 0.3V ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5kV
Thermal Information
Thermal Resistance (Typical, Note 1) JA (oC/W) SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC (SOIC - Lead Tips Only)
Recommended Operating Conditions
Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V 5% Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC
CAUTION: Stress above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied.
NOTE: 1. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. (See Tech Brief TB379 for details.)
Electrical Specifications
PARAMETER INPUT SUPPLY POWER Input Supply Current
Operating Conditions: VCC = 5V, TA = 0oC to 70oC, Unless Otherwise Specified TEST CONDITIONS MIN TYP MAX UNITS
RT = 100k, EN = 5V RT = 100k, EN = 0V 5 4.25 3.75 1.206 1.106 60 EN = 3V
10.5 9.2 4.38 3.86 1.230 1.15
15
mA mA
Power-On Reset Threshold
VCC Rising VCC Falling
4.5 4.0 1.254 1.194 100 50
V V V V mV nA
Enable Threshold
EN Rising EN Falling
Enable Hysteresis Enable Current SYSTEM ACCURACY System Accuracy ISL6557 VID Pull Up VID Input Low Level VID Input High Level (Note 3) OSCILLATOR Accuracy Frequency Adjustment Range Sawtooth Amplitude Duty-Cycle Range ERROR AMPLIFIER Open-Loop Gain Open-Loop Bandwidth Slew Rate Maximum Output Voltage REMOTE-SENSE AMPLIFIER Input Impedance Slew Rate Bandwidth RL = 10k to ground CL = 100pF, RL = 10k to ground CL = 100pF, RL = 10k to ground RL = 10k to ground RT = 110k (1%) (Note 2)
-0.8 -40 -20
0.8 -10 0.8
%VID A V V
2.0
-20 250 80 1.33 0
20
% kHz
1500
kHz V
75
%
72 18 5 3.6 4.1
dB MHz V/s V
80 6 10
k V/s MHz
4
ISL6557
Electrical Specifications
PARAMETER ISEN Overcurrent Trip Level PROTECTION and MONITOR Overvoltage Threshold VSEN Rising VSEN Falling Undervoltage Threshold VSEN Rising VSEN Falling PGOOD Low Voltage NOTES: 2. These parts are designed and adjusted for accuracy within the system tolerance given in the Electrical Specifications. The system tolerance accounts for offsets in the differential and error amplifiers; reference-voltage inaccuracies; temperature drift; and the full DAC adjustment range. 3. VID input levels above 2.9V may produce an reference-voltage offset inaccuracy. IPGOOD = 4mA 0.810 0.835 0.18 2.04 2.09 VID 0.990 0.925 0.4 2.13 V V V V mV -90 -75 -60 A Operating Conditions: VCC = 5V, TA = 0oC to 70oC, Unless Otherwise Specified (Continued) TEST CONDITIONS MIN TYP MAX UNITS
Functional Pin Descriptions
VID4 1 VID3 2 VID2 3 VID1 4 VID0 5 COMP 6 FB 7 IOUT 8 VDIFF 9 VSEN 10 RGND 11 GND 12 24 VCC 23 EN 22 FS 21 PGOOD 20 PWM4 19 ISEN4 18 ISEN1 17 PWM1 16 PWM2 15 ISEN2 14 ISEN3 13 PWM3
input to the external regulation circuitry and the internal protection circuitry. Connect VSEN and RGND to the sense pins of the remote load.
GND (Pin 12)
Return for VCC and signal ground for the IC.
PWM3, PWM2, PWM1, PWM4 (Pins 13, 16, 17, 20)
Pulse-width modulation outputs. These logic outputs tell the driver IC(s) when to turn the MOSFETs on and off.
ISEN3, ISEN2, ISEN1, ISEN4 (PINS 14, 15, 18, 19)
Current sense inputs. A resistor connected between these pins and the respective phase nodes has a current proportional to the current in the lower MOSFET during its conduction interval. The current is used as a reference for channel balancing, load sharing, protection, and load-line regulation.
VID4, VID3, VID2, VID1, VID0 (Pins 1, 2, 3, 4, 5)
These are the inputs to the internal DAC that provides the reference voltage for output regulation. Connect these pins to either open-drain or active-pull-up type outputs. Pulling these pins above 2.9V can cause a reference offset inaccuracy.
PGOOD (Pin 21)
PGOOD is an open-drain logic output that changes to a logic low when the differential output voltage at VDIFF swings below 0.9V or above 2.1V.
FB (Pin 7) and COMP (Pin 6)
The internal error amplifier's inverting input and output respectively. These pins are connected to an external R-C network to compensate the regulator.
FS (Pin 22)
This pin has two functions. A resistor placed from FS to ground sets the switching frequency. There is an inverse relationship between the value of the resistor and the switching frequency. This pin can also be used to disable the controller. To disable the controller, pull this pin below 1V.
IOUT (Pin 8)
The current out of this pin is proportional to output current and is used for load-line regulation and load sharing. The scale factor is set by the ratio of the ISEN resistors (connected to pins 14, 15, 18, and 19) to the lower MOSFET rDS(ON).
EN (Pin 23)
This is the threshold-sensitive enable input for the controller. To enable the controller, pull this pin above 1.23V.
VDIFF (Pin 9), VSEN (Pin 10), RGND (Pin 11)
VSEN and RGND are the inputs to the differential remotesense amplifier. VDIFF is the output and it serves as the 5
VCC (Pin 24)
Bias supply voltage for the controller. Connect this pin to a 5V power supply.
ISL6557
VIN COMP HIP6601A L1
ERROR AMPLIFIER FB +
+ + + -
PWM CIRCUIT
PWM1
PWM CIRCUIT
ISEN1 RISEN1 VIN
DAC & REFERENCE
PWM2
AVERAGE IOUT ISEN2 RISEN2 + HIP6601A + + x1 VDIFF + CURRENT SENSE CURRENT SENSE CURRENT SENSE PWM3 VIN L3
HIP6601A
PWM CIRCUIT
L2
VOUT CO P LOAD
ISEN3 RISEN3
RGND
VSEN
FIGURE 1. SIMPLIFIED BLOCK DIAGRAM OF THE ISL6557 IN A 3-PHASE CONVERTER
Operation
Multi-Phase Power Conversion
Multi-phase power conversion provides the most costeffective power solution when load currents are no longer easily supported by single-phase converters. Although its greater complexity presents additional technical challenges, the multi-phase approach offers cost-saving advantages with improved response time, superior ripple cancellation, and excellent thermal distribution. INTERLEAVING The switching of each channel in a multi-phase converter is timed to be symmetrically out of phase with each of the other channels. In a 4-phase converter, each channel switches 1/4 cycle after the previous channel and 1/4 cycle before the following channel. As a result, the four-phase converter has a combined ripple frequency four times greater than the ripple frequency of any one phase. In addition, the peak-topeak amplitude of the combined inductor currents is reduced in proportion to the number of phases (Equations 1 and 2). Increased ripple frequency and lower ripple amplitude mean 6
that the designer can use less per-channel inductance and lower total output capacitance for any performance specification.
IL1 + IL2 + IL3, 7A/DIV
IL3, 7A/DIV PWM3, 5V/DIV IL2, 7A/DIV PWM2, 5V/DIV IL1, 7A/DIV PWM1, 5V/DIV 1s/DIV
FIGURE 2. PWM AND INDUCTOR-CURRENT WAVEFORMS FOR 3-PHASE CONVERTER
ISL6557
Figure 2 (previous page) illustrates the multiplicative effect on output ripple frequency. The three channel currents (IL1, IL2, and IL3), combine to form the AC ripple current and the DC load current. The ripple component has three times the ripple frequency of each individual channel current. Each PWM pulse is terminated 1/3 of a cycle, or 1.33s, after the PWM pulse of the previous phase. The peak-to-peak current waveforms for each phase is about 7A, and the dc components of the inductor currents combine to feed the load. To understand the reduction of ripple current amplitude in the multi-phase circuit, examine the equation representing an individual channel's peak-to-peak inductor current.
( V IN - V OUT ) V OUT I L, PP = ----------------------------------------------------L fS V
IN
maximum input ripple current. Multi-phase topologies can improve overall system cost and size by lowering input ripple current and allowing the designer to reduce the cost of input capacitance. The example in Figure 3 illustrates input currents from a three-phase converter combining to reduce the total input ripple current. The converter depicted in Figure 3 delivers 36A to a 1.5V load from a 12V input. The rms input capacitor current is 5.9A. Compare this to a single-phase converter also down 12V to 1.5V at 36A. The single-phase converter has 11.9A rms input capacitor current. The single-phase converter must use an input capacitor bank with twice the rms current capacity as the equivalent three-phase converter. Figures 15, 16 and 17 the section entitled Input Capacitor Selection can be used to determine the input-capacitor rms current based on load current, duty cycle, and the number of channels. They are provided as aids in determining the optimal input capacitor solution. Figure 18 shows the single phase input-capacitor rms current for comparisson. PWM OPERATION The number of active channels selected determines the timing for each channel. By default, the timing mode for the ISL6557 is 4-phase. The designer can select 2-phase timing by connecting PWM3 to VCC or 3-phase timing by connecting PWM4 to VCC. One switching cycle for the ISL6557 is defined as the time between PWM1 pulse termination signals (the internal signal that initiates a falling edge on PWM1). The cycle time is the inverse of the switching frequency selected by the resistor connected between the FS pin and ground (see Switching Frequency). Each cycle begins when a clock signal commands the channel-1 PWM output to go low. This signals the channel-1 MOSFET driver to turn off the channel-1 upper MOSFET and turn on the channel-1 synchronous MOSFET. If two-channel operation is selected, the PWM2 pulse terminates 1/2 of a cycle later. If three channels are selected the PWM2 pulse terminates 1/3 of a cycle after PWM1, and the PWM3 output will follow after another 1/3 of a cycle. When four channels are selected, the pulsetermination times are spaced in 1/4 cycle increments. Once a channel's PWM pulse terminates, it remains low for a minimum of 1/4 cycle. This forced off time is required to assure an accurate current sample as described in Current Sensing. Following the 1/4-cycle forced off time, the controller enables the PWM output. Once enabled, the PWM output transitions high when the sawtooth signal crosses the adjusted error-amplifier output signal, VCOMP as illustrated in Figures 1 and 5. This is the signal for the MOSFET driver to turn off the synchronous MOSFET and turn on the upper MOSFET. The output will remain high until the clock signals the beginning of the next cycle by commanding the PWM pulse to terminate.
(EQ. 1)
In Equation 1, VIN and VOUT are the input and output voltages respectively, L is the single-channel inductor value, and fS is the switching frequency.
( V IN - N V OUT ) V OUT I PP = ----------------------------------------------------------L fS V
IN
(EQ. 2)
The output capacitors conduct the ripple component of the inductor current. In the case of multi-phase converters, the capacitor current is the sum of the ripple currents from each of the individual channels. Compare Equation 1 to the expression for the peak-to-peak current after the summation of N symmetrically phase-shifted inductor currents in Equation 2. Peak-to-peak ripple current decreases by an amount proportional to the number of channels. Outputvoltage ripple is a function of capacitance, capacitor equivalent series resistance (ESR), and inductor ripple current. Reducing the inductor ripple current allows the designer to use fewer or less costly output capacitors.
INPUT-CAPACITOR CURRENT, 10A/DIV
CHANNEL 3 INPUT CURRENT 10A/DIV CHANNEL 2 INPUT CURRENT 10A/DIV CHANNEL 1 INPUT CURRENT 10A/DIV 1s/DIV
FIGURE 3. CHANNEL INPUT CURRENTS AND INPUTCAPACITOR RMS CURRENT FOR 3-PHASE CONVERTER
Another benefit of interleaving is to reduce input ripple current. Input capacitance is determined in part by the
7
ISL6557
CURRENT SENSING Intersil multi-phase controllers sense current by sampling the voltage across the lower MOSFET during its conduction interval. MOSFET rDS(ON) sensing is a no-added-cost method to sense current for load-line regulation, channelcurrent balance, module current sharing, and overcurrent protection. If desired, an independent current-sense resistor in series with the lower-MOSFET source can serve as a sense element in place of the MOSFET rDS(ON).
VIN r DS ( ON ) I SEN = I L ------------------------R ISEN CHANNEL N UPPER MOSFET
illustrated in Figure 5 where the average of the 2, 3, or 4 sampled channel currents combines with the channel 1 sample, I1, to create an error signal IER. The filtered error signal modifies the pulse width commanded by VCOMP to correct any unbalance and force IER toward zero. In some circumstances, it may be necessary to deliberately design some channel-current unbalance into the system. In a highly compact design, one or two channels may be able to cool more effectively than the other(s) due to nearby air flow or heat sinking components. The other channel(s) may have more difficulty cooling with comparatively less air flow and heat sinking. The hotter channels may also be located close to other heat-generating components tending to drive their temperature even higher. In these cases, a proper selection of the current sense resistors (RISEN in Figure 4) introduces channel current unbalance into the system. Increasing the value of RISEN in the cooler channels and decreasing it in the hotter channels moves all channels into thermal balance at the expense of current balance. OVERCURRENT PROTECTION The average current, IAVG in Figure 5, is continually compared with a constant 75A reference current. If the average current at any time exceeds the reference current, the comparator triggers the converter to shut down. All PWM signals are placed in a high-impedance state which signals the drivers to turn off both upper and lower MOSFETs. The system remains in this state while the controller counts 2048 phase-clock cycles.
VCOMP + + f(j) IER + SAWTOOTH SIGNAL I4 * IAVG PWM1
In
SAMPLE & HOLD +
IL ISEN(n) RISEN I CHANNEL N LOWER MOSFET + r L DS ( ON )
ISL6557 INTERNAL CIRCUIT
EXTERNAL CIRCUIT
FIGURE 4. INTERNAL AND EXTERNAL CURRENT-SENSING CIRCUITRY
The ISEN input for each channel uses a ground-referenced amplifier to reproduce a signal proportional to the channel current (Figure 4). After sufficient settling time, the sensed current is sampled, and the sample is used for current balance, load-line regulation and overcurrent protection. The ISL6557 samples channel current once each cycle. Figure 4 shows how the sampled current, In, is created from the channel current IL. The circuitry in Figure 4 represents the current measurement and sampling circuitry for channel n in an N-channel converter. This circuitry is repeated for each channel in the converter but may not be active in channels 3 and 4 depending on the particular implementation (see PWM Operation). CHANNEL-CURRENT BALANCE Another benefit of multi-phase operation is the thermal advantage gained by distributing the dissipated heat over multiple devices and greater area. By doing this, the designer avoids the complexity of driving multiple parallel MOSFETs and the expense of using expensive heat sinks and exotic magnetic materials. In order to fully realize the thermal advantage, it is important that each channel in a multi-phase converter be controlled to deliver about the same current at any load level. Intersil multi-phase controllers guarantee current balance by comparing each channel's current to the average current delivered by all channels and making an appropriate adjustment to each channel's pulse width based on the error. Intersil's patented current-balance method is
/N
I3 * I2
I1
FIGURE 5. CHANNEL-1 PWM FUNCTION AND CURRENTBALANCE ADJUSTMENT NOTE: *Channels 3 and 4 are optional.
This is followed by a soft-start attempt (see Soft-Start). If the soft-start attempt is successful, operation will continue as normal. Should the soft-start attempt fail, the ISL6557 repeats the 2048-cycle wait period and follows with another soft-start attempt. This hiccup mode of operation continues
8
ISL6557
indefinitely as shown in Figure 6 as long as the controller is enabled or until the overcurrent condition resolves. The integrating compensation network shown in Figure 7 assures that the steady-state error in the output voltage is limited to the error in the reference voltage (output of the DAC) plus offset errors in the remote-sense and error amplifiers. Intersil specifies the guaranteed tolerance of the ISL6557 and all Intersil controllers to include all variations in the amplifiers and reference so that the output voltage remains within the specified system tolerance.
TABLE 1. VOLTAGE IDENTIFICATION CODES VID4
OUTPUT VOLTAGE, 500mV/DIV
OUTPUT CURRENT, 20A/DIV
0A
VID3 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
VID2 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0
VID1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0
VID0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
VDAC Off 1.100 1.125 1.150 1.175 1.200 1.225 1.250 1.275 1.300 1.325 1.350 1.375 1.400 1.425 1.450 1.475 1.500 1.525 1.550 1.575 1.600 1.625 1.650 1.675 1.700 1.725 1.750 1.775 1.800 1.825 1.850
1 1 1
0V
1
5ms/DIV
1 1
FIGURE 6. OVERCURRENT BEHAVIOR IN HICCUP MODE
VOLTAGE REGULATION The ISL6557 uses a digital to analog converter (DAC) to generate a reference voltage based on the logic signals at pins VID4 to VID0. The DAC decodes the a 5-bit logic signal (VID) into one of the discrete voltages shown in Table 1. Each VID input offers a 20A pull-up to 2.5V for use with open-drain outputs. External pull-up resistors or active-high output stages can augment the pull-up current sources, but a slight accuracy error can occur if they are pulled above 2.9V. The DAC-selected reference voltage is connected to the non-inverting input of the error amplifier, and the output of the differential remote-sense amplifier usually gets connected to the error amplifier as shown in Figure 7. The remote-sense amplifier eliminates voltage differences between local and remote ground to provide a more accurate means of sensing outputvoltage.
.
1 1 1 1 1 1 1 1 1 1 0 0 0 0 0
EXTERNAL CIRCUIT RC CC COMP
ISL6557 INTERNAL CIRCUIT
0
ERROR AMPLIFIER
0 0
FB + VDROOP VDIFF IAVG
+ VCOMP
RFB
IOUT
0 0 0 0
REFERENCE VOLTAGE
VOUT
VSEN +
0 0
-
REMOTE GROUND
RGND
0
DIFFERENTIAL REMOTE-SENSE AMPLIFIER
0
FIGURE 7. OUTPUT VOLTAGE AND LOAD-LINE REGULATION
9
ISL6557
OVERVOLTAGE PROTECTION The ISL6557 detects output voltages above 2.1V and immediately commands all PWM outputs low. This directs the Intersil drivers turn on the lower MOSFETs and protect the load by preventing any further increase in output voltage. Once the output voltage falls to the level set by the VID code, the PWM outputs enter high-impedance mode. The Intersil drivers respond by turning off both upper and lower MOSFETs. If the overvoltage condition reoccurs, the ISL6557 will again command the lower MOSFETs to turn on. The ISL6557 will continue to protect the load in this fashion as long as the overvoltage repeats. After detecting an overvoltage condition, the ISL6557 ceases normal PWM operation until it is reset by power cycle in which VCC is removed below the POR falling threshold and restored above the POR rising threshold as described in Enable and Disable and Electrical Specifications. LOAD-LINE REGULATION In applications with high transient current slew rates, the lowest-cost solution for maintaining regulation often requires some kind of controlled output impedance. Pin 8 of the ISL6557 carries a current proportional to the average current of all active channels. The current is equivalent to IAVG in Figures 5 and 7. Connecting FB and IOUT together forces IAVG into the summing node of the error amplifier and produces a voltage drop across the feedback resistor, RFB, proportional to the output current. In Figure 7, the steadystate value of VDROOP is simply
V DROOP = I AVG R FB (EQ. 3)
is below the POR-rising threshold, the PWM outputs are held in a high-impedance state to assure the drivers remain off.
ISL6557 INTERNAL CIRCUIT EXTERNAL CIRCUIT +5V VCC ENABLE COMPARATOR EN POR CIRCUIT + 1.23V ( 2%) 1.40k +12V
10.7k
OV LATCH SIGNAL
FIGURE 8. START-UP CONDITION USING THRESHOLDSENSITIVE ENABLE (EN) FUNCTION
After power on, the ISL6557 remains in shut-down mode until the voltage at the enable input (EN) rises above 1.23V (2%). This optional feature prevents the ISL6557 from operating until the connected voltage rail is available and above some selectable threshold. For example, the HIP660X family of MOSFET driver ICs require 12V bias, and in certain circumstances, it can be important to assure that the drivers reach their POR level before the ISL6557 becomes enabled. The schematic in Figure 8 demonstrates coordination of the ISL6557 with HIP660X family of MOSFET driver ICs. The enable comparator has about 70mV of hysteresis to prevent bounce. To defeat the threshold-sensitive enable, connect EN to VCC. The 11111 VID code is reserved as a signal to the controller that no load is present. The controller will enter shut-down mode after receiving this code and will start up upon receiving any other code. To enable the controller, VCC must be greater than the POR threshold; the voltage on EN must be greater than 1.23V; and VID cannot be equal to 11111. Once these conditions are true, the controller immediately initiates a soft start sequence. SOFT-START The soft-start time, tSS, is determined by an 11-bit counter that increments with every pulse of the phase clock. For example, a converter switching at 250kHz has a soft-start time of
2048 T SS = ------------ = 8.2ms f SW (EQ. 5)
In the case that each channel uses the same value for RISEN to sense channel current, and this is almost always true, a more complete expression for VDROOP can be determined from the expression for IAVG as it is derived from Figures 4 and 5.
I OUT r DS ( ON ) I AVG = ------------ ---------------------N R ISEN I OUT r DS ( ON ) V DROOP = ------------ ---------------------- R FB N R ISEN (EQ. 4)
ENABLE AND DISABLE The internal power-on reset circuit (POR) prevents the ISL6557 from starting before the bias voltage at VCC reaches the POR-rising threshold as defined in Electrical Specifications.The POR level is high enough to guarantee that all parts of the ISL6557 can perform their functions properly. Built-in hysteresis assures that once enabled, the ISL6557 will not turn off unless the bias voltage falls to approximately 0.5V below the POR-rising level. When VCC
10
ISL6557
During the soft-start interval, the soft-start voltage, VRAMP , increases linearly from zero to 140% of the programmed DAC voltage. At the same time a current source, IRAMP , is decreasing from 160A down to zero. These signals are connected as shown in Figure 9 (IOUT may or may not be connected to FB depending on the particular application).
EXTERNAL CIRCUIT RC CC COMP ERROR AMPLIFIER FB EN, 5V/DIV ISL6557 INTERNAL CIRCUIT
VOUT, 500mV/DIV
+
IRAMP VRAMP IAVG IDEAL DIODES VCOMP REFERENCE VOLTAGE 1ms/DIV
RFB
IOUT
VDIFF
tDELAY tRAMP1
tRAMP2
FIGURE 10. SOFT-START WAVEFORMS FOR ISL6557 BASED MULTI-PHASE BUCK CONVERTER NOTE: Switching frequency 500kHz and RFB = 2.67k
DYNAMIC VID The ISL6557 is capable of executing on-the-fly outputvoltage changes. At the beginning of the phase-1 switching cycle (defined in the section entitled PWM Operation), the ISL6557 checks for a change in the VID code. The VID code is the bit pattern present at pins VID4-VID0 as outlined in Voltage Regulation. If the new code remains stable for another full cycle, the ISL6557 begins incrementing the reference by making 25mV change every two switching cycles until the it reaches the new VID code.
01110 00110 VID, 5V/DIV VID CHANGE OCCURS ANYWHERE HERE
FIGURE 9. RAMP CURRENT AND VOLTAGE FOR REGULATING SOFT-START SLOPE AND DURATION
The ideal diodes in Figure 9 assure that the controller tries to regulate its output to the lower of either the reference voltage or VRAMP. Since IRAMP creates an initial offset across RFB of RFB times 160mA, the first PWM pulses will not be seen until VRAMP is greater than the RFB IRAMP offset. This produces a delay after the ISL6557 enables before the output voltage starts moving. For example, if VID = 1.5V, RFB = 1k and TSS = 8.3ms, the delay can be expressed using Equation 6.
T SS t DELAY = -------------------------------------------------- = 580s 1.4 ( VID) 1 + ---------------------------------------R FB 160 x 10 - 6 (EQ. 6)
VREF, 100mV/DIV
From this point, the soft-start ramps linearly until VRAMP reaches VID. For the system described above, this first linear ramp will continue for approximately
T SS t RAMP1 = ---------- - t DELAY 1.4 = 5.27ms (EQ. 7)
1.5V
VOUT, 100mV/DIV 1.5V
The final portion of the soft-start sequence is the time remaining after VRAMP reaches VID and before IRAMP gets to zero. This is also characterized by a slight linear ramp in the output voltage which, for the current example, exists for a time
t RAMP2 = T SS - t RAMP1 - t DELAY = 2.34ms (EQ. 8)
5s/DIV
FIGURE 11. DYNAMIC-VID WAVEFORMS FOR 500kHZ ISL6557 BASED MULTI-PHASE BUCK CONVERTER
This behavior is seen in the example in Figure 10 of a converter switching at 500kHz. For this converter, RFB is set to 2.67k leading to TSS = 4.0ms, tDELAY = 700ns, tRAMP1 = 2.23ms, and tRAMP2 = 1.17ms.
Since the ISL6557 recognizes VID-code changes only at the beginnings of switching cycles, up to one full cycle may pass before a VID change registers. This is followed by a onecycle wait before the output voltage begins to change. Thus, the total time required for a VID change, tDV, is dependent on the switching frequency (fS), the size of the change (VID), and the time before the next switching cycle begins.
11
ISL6557
The one-cycle uncertainty in Equation 9 is due to the possibility that the VID code change may occur up to one full cycle before being recognized. The time required for a converter running with fS = 500kHz to make a 1.5V to 1.7V reference-voltage change is between 30s and 32s as calculated using Equation 9. This example is also illustrated in Figure 11.
1 2 V ID 1 2 V ID ---- ---------------- - 1 < t DV ---- ---------------- f S 0.025 f S 0.025 (EQ. 9)
An additional term can be added to the lower-MOSFET loss equation to account for additional loss accrued during the dead time when inductor current is flowing through the lower-MOSFET body diode. This term is dependent on the diode forward voltage at IM, VD(ON); the switching frequency, fS; and the length of dead times, td1 and td2, at the beginning and the end of the lower-MOSFET conduction interval respectively.
I M I PP IM I P LOW , 2 = V D ( ON ) f S ----- + -------- t + ----- - -------- t d2 - PP 2 d1 N 2 N (EQ. 11)
General Design Guide
This design guide is intended to provide a high-level explanation of the steps necessary to create a multi-phase power converter. It is assumed that the reader is familiar with many of the basic skills and techniques referenced below. In addition to this guide, Intersil provides complete reference designs that include schematics, bills of materials, and example board layouts for all common microprocessor applications.
Thus the total power dissipated in each lower MOSFET is approximated by the summation of PL and PD. UPPER MOSFET POWER CALCULATION In addition to rDS(ON) losses, a large portion of the upperMOSFET losses are due to currents conducted across the input voltage (VIN) during switching. Since a substantially higher portion of the upper-MOSFET losses are dependant on switching frequency, the power calculation is somewhat more complex. Upper MOSFET losses can be divided into separate components involving the upper-MOSFET switching times; the lower-MOSFET body-diode reverserecovery charge, Qrr; and the upper MOSFET rDS(ON) conduction loss. When the upper MOSFET turns off, the lower MOSFET does not conduct any portion of the inductor current until the voltage at the phase node falls below ground. Once the lower MOSFET begins conducting, the current in the upper MOSFET falls to zero as the current in the lower MOSFET ramps up to assume the full inductor current. In Equation 12, the required time for this commutation is t1and the associated power loss is PUP,1.
I M I L ,PP t 1 P UP,1 V IN ----- + ------------ ---- f S 2 2 N (EQ. 12)
Power Stages
The first step in designing a multi-phase converter is to determine the number of phases. This determination depends heavily on the cost analysis which in turn depends on system constraints that differ from one design to the next. Principally, the designer will be concerned with whether components can be mounted on both sides of the circuit board; whether through-hole components are permitted on either side; and the total board space available for powersupply circuitry. Generally speaking, the most economical solutions will be for each phase to handle between 15A and 20A. All-surface-mount designs will tend toward the lower end of this current range and, if through-hole MOSFETs can be used, higher per-phase currents are possible. In cases where board space is the limiting constraint, current can be pushed as high as 30A per phase, but these designs require heat sinks and forced air to cool the MOSFETs.
MOSFETs
The choice of MOSFETs depends on the current each MOSFET will be required to conduct; the switching frequency; the capability of the MOSFETs to dissipate heat; and the availability and nature of heat sinking and air flow. LOWER MOSFET POWER CALCULATION The calculation for heat dissipated in the lower MOSFET is simple, since virtually all of the heat loss in the lower MOSFET is due to current conducted through the channel resistance (rDS(ON)). In Equation 10, IM is the maximum continuous output current; IL,PP is the peak-to-peak inductor current (see Equation 1); d is the duty cycle (VOUT/VIN); and L is the per-channel inductance.
I L ,PP ( 1 - d ) I M 2 P LOW ,1 = r DS ( ON ) ----- ( 1 - d ) + -----------------------------12 N
2
Similarly, the upper MOSFET begins conducting as soon as it begins turning on. In Equation 13, this transition occurs over a time t2, and the approximate the power loss is PUP,2.
I M I L ,PP t 2 P UP, 2 V IN ----- - ------------ ---- f S 2 2 N (EQ. 13)
A third component involves the lower MOSFET's reverserecovery charge, Qrr. Since the inductor current has fully commutated to the upper MOSFET before the lowerMOSFET's body diode can recover all of Qrr, it is conducted through the upper MOSFET across VIN. The power dissipated as a result is PUP,3 and is simply
P UP,3 = V IN Q rr f S (EQ. 14)
(EQ. 10)
12
ISL6557
Finally, the resistive part of the upper MOSFET's is given in Equation 15 as PUP,4.
2 I PP I M P UP,4 = r DS ( ON ) ----- d + --------12 N 2
ISEN resistor, the load-line regulation resistor is as shown in Equation 18.
V DROOP R FB = ------------------------6 50 x10 (EQ. 18)
(EQ. 15)
In this case, of course, rDS(ON) is the on resistance of the upper MOSFET. The total power dissipated by the upper MOSFET at full load can now be approximated as the summation of the results from Equations 12, 13, 14 and 15. Since the power equations depend on MOSFET parameters, choosing the correct MOSFETs can be an iterative process that involves repetitively solving the loss equations for different MOSFETs and different switching frequencies until converging upon the best solution.
If one or more of the ISEN resistors was adjusted for thermal balance as in Equation 17, the load-line regulation resistor should be selected according to Equation19 where IFL is the full-load operating current and RISEN(n) is the ISEN resistor connected to the nth ISEN pin.
V DROOP R FB = -------------------------------I FL r DS ( ON )
RISEN ( n )
n
(EQ. 19)
Compensation
The two opposing goals of compensating the voltage regulator are stability and speed. Depending on whether the regulator employs the optional load-line regulation as described in Load-Line Regulation, there are two distinct methods for achieving these goals. COMPENSATING A LOAD-LINE REGULATED CONVERTER The load-line regulated converter behaves in a similar manner to a peak-current mode controller because the two poles at the output-filter L-C resonant frequency split with the introduction of current information into the control loop. The final location of these poles is determined by the system function, the gain of the current signal, and the value of the compensation components, RC and CC. Since the system poles and zero are effected by the values of the components that are meant to compensate them, the solution to the system equation becomes fairly complicated. Fortunately there is a simple approximation that comes very close to an optimal solution. Treating the system as though it were a voltage-mode regulator by compensating the L-C poles and the ESR zero of the voltage-mode approximation yields a solution that is always stable with very close to ideal transient performance.
C2 (OPTIONAL)
Current Sensing
Pins 18, 15, 14 and 19 are the ISEN pins denoted ISEN1, ISEN2, ISEN3 and ISEN4 respectively. The resistors connected between these pins and the phase nodes determine the gains in the load-line regulation loop and the channel-current balance loop. Select the values for these resistors based on the room temperature rDS(ON) of the lower MOSFETs; the full-load operating current, IFL; and the number of phases, N, according to Equation 16 (see also Figure 4).
r DS ( ON ) R ISEN = ---------------------50 x10 - 6 I FL ------N (EQ. 16)
In certain circumstances, it may be necessary to adjust the value of one or more of the ISEN resistors. This can arise when the components of one or more channels are inhibited from dissipating their heat so that the affected channels run hotter than desired (see the section entitled Channel-Current Balance). In these cases, chose new, smaller values of RISEN for the affected phases. Choose RISEN,2 in proportion to the desired decrease in temperature rise in order to cause proportionally less current to flow in the hotter phase.
T 2 R ISEN ,2 = R ISEN ---------T 1 (EQ. 17)
In Equation 17, make sure that T2 is the desired temperature rise above the ambient temperature, and T1 is the measured temperature rise above the ambient temperature. While a single adjustment according to Equation 17 is usually sufficient, it may occasionally be necessary to adjust RISEN two or more times to achieve perfect thermal balance between all channels.
RC
CC
COMP
FB + RFB VDROOP VDIFF
IOUT
Load-Line Regulation Resistor
The load-line regulation resistor is labeled RFB in Figure 7. Its value depends on the desired full-load droop voltage (VDROOP in Figure 7). If Equation 16 is used to select each
FIGURE 12. COMPENSATION CONFIGURATION FOR LOAD-LINE REGULATED ISL6557 CIRCUIT
13
ISL6557
ISL6557
The feedback resistor, RFB, has already been chosen as outlined in Load-Line Regulation Resistor. Select a target bandwidth for the compensated system, f0. The target bandwidth must be large enough to assure adequate transient performance, but smaller than 1/3 of the perchannel switching frequency. The values of the compensation components depend on the relationships of f0 to the L-C pole frequency and the ESR zero frequency. For each of the three cases defined below, there is a separate set of equations for the compensation components. Case 1:
1 ------------------- > f 0 2 LC 2f 0 V pp LC R C = R FB ----------------------------------0.75V
IN C1 R1 RFB
COMPENSATION WITHOUT LOAD-LINE REGULATION The non load-line regulated converter is accurately modeled as a voltage-mode regulator with two poles at the L-C resonant frequency and a zero at the ESR frequency. A type III controller, as shown in Figure 13, provides the necessary compensation.
C2
RC
CC
COMP
FB + VDROOP VDIFF ISL6557
0.75V IN C C = ----------------------------------2V PP R FB f 0
IOUT
Case 2:
1 1 ------------------- f 0 < ----------------------------2C ( ESR ) 2 LC V PP ( 2 ) f 0 LC R C = R FB -------------------------------------------0.75 V IN 0.75V IN C C = -----------------------------------------------------------( 2 ) 2 f 02 V PP R FB LC
2 2
(EQ. 20)
FIGURE 13. COMPENSATION CIRCUIT FOR ISL6557 BASED CONVERTER WITHOUT LOAD-LINE REGULATION.
Case 3:
1 f 0 > ----------------------------2C ( ESR ) 2 f 0 V pp L R C = R FB ----------------------------------------0.75 V IN ( ESR ) 0.75V IN ( ESR ) C C C = -----------------------------------------------2V PP R FB f 0 L
The first step is to choose the desired bandwidth, f0, of the compensated system. Choose a frequency high enough to assure adequate transient performance but not higher than 1/3 of the switching frequency. The type-III compensator has an extra high-frequency pole, fHF. This pole can be used for added noise rejection or to assure adequate attenuation at the error-amplifier high-order pole and zero frequencies. A good general rule is to chose fHF = 10 f0, but it can be higher if desired. Choosing fHF to be lower than 10 f0 can cause problems with too much phase shift below the system bandwidth. In the solutions to the compensation equations, there is a single degree of freedom. For the solutions presented in Equations 21, RFB is selected arbitrarily. The remaining compensation components are then selected according to Equations 21.
C ( ESR ) R 1 = R FB ---------------------------------------LC - C ( ESR ) LC - C ( ESR ) C 1 = ---------------------------------------R FB 0.75V IN C 2 = -----------------------------------------------------------------( 2 ) 2 f 0 f HF LCR FB V PP R FB V 2 f 0 f HF LC PP R C = --------------------------------------------------------------0.75V IN 2f HF LC - 1 0.75V IN 2f HF LC - 1 C C = ------------------------------------------------------------------ 2 2 V R f f LC PP FB 0 HF
2
In Equations 20, L is the per-channel filter inductance divided by the number of active channels; C is the sum total of all output capacitors; ESR is the equivalent-series resistance of the bulk output-filter capacitance; and VPP is the peak-to-peak sawtooth signal amplitude as described in Figure 5 and Electrical Specifications. Once selected, the compensation values in Equations 20 assure a stable converter with reasonable transient performance. In most cases, transient performance can be improved by making adjustments to RC. Slowly increase the value of RC while observing the transient performance on an oscilloscope until no further improvement is noted. Normally, CC will not need adjustment. Keep the value of CC from Equations 20 unless some performance issue is noted. The optional capacitor C2, is sometimes needed to bypass noise away from the PWM comparator (see Figure 5). Keep a position available for C2, and be prepared to install a highfrequency capacitor of between 22pF and 150pF in case any jitter problem is noted.
(EQ. 21)
14
ISL6557
In Equations 21, L is the per-channel filter inductance divided by the number of active channels; C is the sum total of all output capacitors; ESR is the equivalent-series resistance of the bulk output-filter capacitance; and VPP is the peak-to-peak sawtooth signal amplitude as described in Figure 5 and Electrical Specifications. The ESR of the bulk capacitors also creates the majority of the output-voltage ripple. As the bulk capacitors sink and source the inductor AC ripple current (see Interleaving and Equation 2), a voltage develops across the bulk-capacitor ESR equal to IPP (ESR). Thus, once the output capacitors are selected, the maximum allowable ripple voltage, VPP(MAX), determines the a lower limit on the inductance.
V - N V OUT V OUT IN L ( ESR ) ----------------------------------------------------------f S V IN V PP( MAX ) (EQ. 23)
Output Filter Design
The output inductors and the output capacitor bank together form a low-pass filter responsible for smoothing the pulsating voltage at the phase nodes. The output filter also must provide the transient energy during the interval of time after the beginning of the transient until the regulator can fully respond. Because it has a low bandwidth compared to the switching frequency, the output filter necessarily limits the system transient response leaving the output capacitor bank to supply or sink load current while the current in the output inductors increases or decreases to meet the demand. In high-speed converters, the output capacitor bank is usually the most costly (and often the largest) part of the circuit. Output filter design begins with minimizing the cost of this part of the circuit. The critical load parameters in choosing the output capacitors are the maximum size of the load step, I; the load-current slew rate, di/dt; and the maximum allowable output-voltage deviation under transient loading, VMAX. Capacitors are characterized according to their capacitance, ESR, and ESL (equivalent series inductance). At the beginning of the load transient, the output capacitors supply all of the transient current. The output voltage will initially deviate by an amount approximated by the voltage drop across the ESL. As the load current increases, the voltage drop across the ESR increases linearly until the load current reaches its final value. The capacitors selected must have sufficiently low ESL and ESR so that the total outputvoltage deviation is less than the allowable maximum. Neglecting the contribution of inductor current and regulator response, the output voltage initially deviates by an amount
di V ( ESL ) ---- + ( ESR ) I dt (EQ. 22)
Since the capacitors are supplying a decreasing portion of the load current while the regulator recovers from the transient, the capacitor voltage becomes slightly depleted. The output inductors must be capable of assuming the entire load current before the output voltage decreases more than VMAX. This places an upper limits on inductance.
2NCVO L -------------------- V MAX - I ( ESR ) ( I ) 2 (EQ. 24)
( 1.25 ) NC L ------------------------- V MAX - I ( ESR ) V IN - V O ( I ) 2
(EQ. 25)
Equation 24 gives the upper limit on L for the cases when the trailing edge of the current transient causes a greater output-voltage deviation than the leading edge. Equation 25 addresses the leading edge. Normally, the trailing edge dictates the selection of L because duty cycles are usually less than 50%. Nevertheless, both inequalities should be evaluated, and L should be selected based on the lower of the two results. In each equation, L is the per-channel inductance, C is the total output capacitance, and N is the number of active channels.
Switching Frequency
There are a number of variables to consider when choosing the switching frequency. There are considerable effects on the upper-MOSFET loss calculation and, to a lesser extent, the lower-MOSFET loss calculation. These effects are outlined in MOSFETs, and they establish the upper limit for the switching frequency. The lower limit is established by the requirement for fast transient response and small outputvoltage ripple as outlined in Output Filter Design. Choose the lowest switching frequency that allows the regulator to meet the transient-response requirements.
The filter capacitor must have sufficiently low ESL and ESR so that V < VMAX. Most capacitor solutions rely on a mixture of high-frequency capacitors with relatively low capacitance in combination with bulk capacitors having high capacitance but limited high-frequency performance. Minimizing the ESL of the high-frequency capacitors allows them to support the output voltage as the current increases. Minimizing the ESR of the bulk capacitors allows them to supply the increased current with less output voltage deviation.
15
ISL6557
Switching frequency is determined by the selection of the frequency-setting resistor,RT (see the figure Typical Application on page 3). Figure 14 and Equation 26 are provided to assist in the selecting the correct value for RT.
1000 0.3 INPUT-CAPACITOR CURRENT ( IRMS / IO )
IL,PP = 0 IL,PP = 0.25 IO
IL,PP = 0.5 IO IL,PP = 0.75 IO
0.2
0.1
RT (k)
100
0
0
0.2
0.4
0.6
0.8
1.0
DUTY CYCLE ( VIN / VO )
10
FIGURE 16. NORMALIZED INPUT-CAPACITOR RMS CURRENT vs DUTY CYCLE FOR 3-PHASE CONVERTER
10 100 1000 SWITCHING FREQUENCY (kHZ) 10000 0.3 INPUT-CAPACITOR CURRENT ( IRMS / IO )
FIGURE 14. RT vs SWITCHING FREQUENCY
[11.09 - 1.13 log ( f S ) ]
IL,PP = 0 IL,PP = 0.25 IO
IL,PP = 0.5 IO IL,PP = 0.75 IO
RT = 10
(EQ. 26)
0.2
Input Capacitor Selection
The input capacitors are responsible for sourcing the ac component of the input current flowing into the upper MOSFETs. Their rms current capacity must be sufficient to handle the ac component of the current drawn by the upper MOSFETs which is related to duty cycle and the number of active phases. Figures 15, 16 and 17 can be used to determine the inputcapacitor rms current as of duty cycle, maximum sustained output current (IO), and the ratio of the combined peak-topeak inductor current (IL,PP as defined in Eqation 1) to the maximum sustained load current, IO. Figure 18 is provided as a reference to demonstrate the dramatic reductions in input-capacitor rms current upon the implementation of the multiphase topology.
0.3 INPUT-CAPACITOR CURRENT ( IRMS / IO )
0.1
0
0
0.2
0.4
0.6
0.8
1.0
DUTY CYCLE ( VIN / VO )
FIGURE 17. NORMALIZED INPUT-CAPACITOR RMS CURRENT vs DUTY CYCLE FOR 4-PHASE CONVERTER
0.6 INPUT-CAPACITOR CURRENT ( IRMS / IO )
0.4
0.2
0.2
0.1
IL,PP = 0 IL,PP = 0.5 IO IL,PP = 0.75 IO
0 0 0.2 0.4 0.6 0.8 1.0
IL,PP = 0 IL,PP = 0.5 IO IL,PP = 0.75 IO
0 0 0.2 0.4 0.6 0.8 1.0 DUTY CYCLE ( VIN / VO )
DUTY CYCLE ( VIN / VO )
FIGURE 15. NORMALIZED INPUT-CAPACITOR RMS
FIGURE 18. NORMALIZED INPUT-CAPACITOR RMS CURRENT vs DUTY CYCLE FOR SINGLE-PHASE CONVERTER
16
ISL6557 Small Outline Plastic Packages (SOIC)
N INDEX AREA E -B1 2 3 SEATING PLANE -AD -CA h x 45o H 0.25(0.010) M BM
M24.3 (JEDEC MS-013-AD ISSUE C)
24 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE INCHES SYMBOL A
L
MILLIMETERS MIN 2.35 0.10 0.33 0.23 15.20 7.40 MAX 2.65 0.30 0.51 0.32 15.60 7.60 NOTES 9 3 4 5 6 7 8o Rev. 0 12/93
MIN 0.0926 0.0040 0.013 0.0091 0.5985 0.2914
MAX 0.1043 0.0118 0.020 0.0125 0.6141 0.2992
A1 B C D E

A1 0.10(0.004) C
e H h L N
0.05 BSC 0.394 0.010 0.016 24 0o 8o 0.419 0.029 0.050
1.27 BSC 10.00 0.25 0.40 24 0o 10.65 0.75 1.27
e
B 0.25(0.010) M C AM BS
NOTES: 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 17

▲Up To Search▲

Price & Availability of ISL6557CB

	To Download ISL6557CB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .